Tesisat Ders İçerikleri

EĞT - 401 SCHOOL EXPERIENCE - II (2 0 2 : 3)

At schools, a practise with advising a teacher observations and lectures have been made for aim of being base on teaching lecture some observations and lecture subject, to explain and directive question for teaching, lecture management and control of lessen, investigation on a student, to appraise study of a student, planning of a lecture, make a good use of lecture books, group study, organisation of lesson, prepare and use of study documents, micro teaching, lecture in glass

EĞT - 403 SPECIAL TEACHING TECHNIQUES - II (2 0 2 : 3)

Teaching methods on this subject. Teaching-learning during education, subject areas of general teaching methods of lecture of learning. Special teaching methods and to regardless with strategies, micro teaching lectures, appraise of teaching

EĞT - 405 LECTURER PRACTICE (2 0 6 : 5)

A day or half day during min 12 week, teacher candidates, for attaining teaching talents on the supervisor of experience teacher. Candidates gives a seminar about technical teaching practice and learn to make a plan a daily and weekly.

ENR - 425 FLUID DYNAMICS - II (3 0 0 : 3)

Fluid properties (viscosity, weight density, vapour pressure, capillarity) are measured in laboratory. Drag and lift. Pipe flows losses load measurement. Velocity of fluids are measured and applicated with continuity equation in pipe flows. Calculation of fluids machines and other machines capacity and power generation.

TES - 421 HEAT PROJECT (2 0 2 : 3)

Domestic hot water heat systems are projected. Drawing and calculating of applications. Calculation of heaters and theirs lay out. Cost of boiler, expansion tank, coal, pipes and applications.

TES - 423 PROTTOTYPE DEVELOPING AND APPLICATIONS (4 0 2 : 5)

Each student takes heating, air conditioning, cooling, sanitary, refrigerating subjects which are plumbing education area. These students research results to their class. Thus, they gain and develop presentation of seminar. The next semester, these students make prototype with their research subjects.

TES - 427 VENTILATING AND AIR CONDITIONING SYSTEM DESIGN (2 0 0 : 2)

Using materials of ventilating and air conditioning, introduction of these materials, theirs capacity and power calculations. Necessity of refresh air calculations. Power and capacity of air conditioning systems calculations. Heat gains and loss calculations.

TES - 429 REFRIGERATION SYSTEMS AND DESIGN (2 0 0 : 2)

Introduction of refrigeration system. Refrigeration system components; (refrigerators, deep freeze, expansion value, evaporator, condenser), refrigeration rooms, heat gains calculation, Vapour-Compression refrigeration cycle.

TES - 431 GAS-FUEL TECHNOLOGY (2 0 0 : 2)

Introduction of gasses in sanitary, Types of gas fuel, gas welding, law of gasses, alternative energy sources of natural gas, natural gas storage, stations of pressure drop, plumbing materials, natural gas using in houses, natural gases combustion.

TES - 433 COMBUSTION TECHNIQUE APPLICATION (3 0 0 : 3)

Combustion of gases, liquid and solid fuels, air-fuel mixtures, combustion gases analysis, combustion chamber design, fuel storage, fuel necessity, gas pipe and safety components, ignition systems, make experiment in lab.

TES - 435 PUMPS (OPS.) (3 0 0 : 3)

Introduction of pumps, viscosity, loss numbers, types of flow, pressure measurement. Euler equation, pumps characteristic, power, efficiency, cavitation. Pumps systems and accumulators. Application of pumps experiment.

TES - 437 INDUSTRIAL AIR CONDITIONING AND REFRIGERATION (OPS.) (3 0 0 : 3)

Air condition and refrigerating systems are projected. Automatic control, refrigeration tower design, split and window type, hospital type air-conditioner. HVAC systems.

TES - 439 BOILER AND IGNITORS (3 0 0 : 3)

Grading of boiler and property, combustion, solid, liquid and gas combustion air, gas of combustion, analysis of combustion gas and combustion efficiency effect, combustion kinds, stacks. Feeding (charging), manual, automatic and fuel injection, combustion chambers, grinding, combustion room, temperature of combustion chamber and calculations.